(06-07-2016, 12:37)QRP73 napisał(a): Przeczytalem caly watek i powiem tak, duzo postow malo konkretow.
Mam DiscoverySTM32F429I, kwarc 8Mhz. Jak ustawic CoreClock za pomoca funkcji CMSIS na 168Mhz ?
Bede wdzieczny za kod z opisem co i dlaczego. Moze jakis autorski SysemInit().
Ogladam kod funkcji SystemInit i trudno sie w tym polapac.
No i wlasnie kolega Marek potwierdzil to o czym pisze... zaczyna sie problem bo brak wiadomosci o tym jak to poustawiac.
No i teraz w sumie pytanie czy lecimy z kodem - czy zrobic opis jak sie ustawia zegary ?
Natomiast co do migania LED-em to przykladowy kod z libopencm3. Jednak trudno to porownac - tutaj nie wymagane jest grzebanie w jakichkolwiek innych plkach do main.c wystarczy dolinkowac bibloteke... ale tego nie zrobi sie kreatorem...
Kod:
/*
* This file is part of the libopencm3 project.
*
* Copyright (C) 2009 Uwe Hermann <uwe@hermann-uwe.de>
* Copyright (C) 2011 Damjan Marion <damjan.marion@gmail.com>
* Copyright (C) 2011 Mark Panajotovic <marko@electrontube.org>
* Copyright (C) 2015 Piotr Esden-Tempski <piotr@esden.net>
*
* This library is free software: you can redistribute it and/or modify
* it under the terms of the GNU Lesser General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public License
* along with this library. If not, see <http://www.gnu.org/licenses/>.
*/
#include <libopencm3/stm32/rcc.h>
#include <libopencm3/stm32/gpio.h>
/* Set STM32 to 168 MHz. */
static void clock_setup(void)
{
rcc_clock_setup_hse_3v3(&rcc_hse_8mhz_3v3[RCC_CLOCK_3V3_168MHZ]);
/* Enable GPIOG clock. */
rcc_periph_clock_enable(RCC_GPIOG);
}
static void gpio_setup(void)
{
/* Set GPIO13-14 (in GPIO port G) to 'output push-pull'. */
gpio_mode_setup(GPIOG, GPIO_MODE_OUTPUT,
GPIO_PUPD_NONE, GPIO13 | GPIO14);
}
int main(void)
{
int i;
clock_setup();
gpio_setup();
/* Set two LEDs for wigwag effect when toggling. */
gpio_set(GPIOG, GPIO13);
/* Blink the LEDs (PG13 and PG14) on the board. */
while (1) {
/* Toggle LEDs. */
gpio_toggle(GPIOG, GPIO13 | GPIO14);
for (i = 0; i < 6000000; i++) { /* Wait a bit. */
__asm__("nop");
}
}
return 0;
}kolejny przyklad z biblioteki z uzyciem systick dla funkcji opoznienia:
Kod:
/*
* This file is part of the libopencm3 project.
*
* Copyright (C) 2009 Uwe Hermann <uwe@hermann-uwe.de>
* Copyright (C) 2011 Damjan Marion <damjan.marion@gmail.com>
* Copyright (C) 2011 Mark Panajotovic <marko@electrontube.org>
* Copyright (C) 2013 Chuck McManis <cmcmanis@mcmanis.com>
* Copyright (C) 2015 Piotr Esden-Tempski <piotr@esden.net>
*
* This library is free software: you can redistribute it and/or modify
* it under the terms of the GNU Lesser General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public License
* along with this library. If not, see <http://www.gnu.org/licenses/>.
*/
/* This version derived from fancy blink */
#include <libopencm3/stm32/rcc.h>
#include <libopencm3/stm32/gpio.h>
#include <libopencm3/cm3/nvic.h>
#include <libopencm3/cm3/systick.h>
/* monotonically increasing number of milliseconds from reset
* overflows every 49 days if you're wondering
*/
volatile uint32_t system_millis;
/* Called when systick fires */
void sys_tick_handler(void)
{
system_millis++;
}
/* sleep for delay milliseconds */
static void msleep(uint32_t delay)
{
uint32_t wake = system_millis + delay;
while (wake > system_millis);
}
/*
* systick_setup(void)
*
* This function sets up the 1khz "system tick" count. The SYSTICK counter is a
* standard feature of the Cortex-M series.
*/
static void systick_setup(void)
{
/* clock rate / 1000 to get 1mS interrupt rate */
systick_set_reload(168000);
systick_set_clocksource(STK_CSR_CLKSOURCE_AHB);
systick_counter_enable();
/* this done last */
systick_interrupt_enable();
}
/* Set STM32 system clock to 168 MHz. */
static void clock_setup(void)
{
rcc_clock_setup_hse_3v3(&rcc_hse_8mhz_3v3[RCC_CLOCK_3V3_168MHZ]);
/* Enable GPIOG clock. */
rcc_periph_clock_enable(RCC_GPIOG);
}
static void gpio_setup(void)
{
/* Set GPIO13-14 (in GPIO port G) to 'output push-pull'. */
gpio_mode_setup(GPIOG, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE,
GPIO13 | GPIO14);
}
int main(void)
{
clock_setup();
gpio_setup();
systick_setup();
/* Set two LEDs for wigwag effect when toggling. */
gpio_set(GPIOG, GPIO13);
/* Blink the LEDs (PG13 and PG14) on the board. */
while (1) {
gpio_toggle(GPIOG, GPIO13 | GPIO14);
msleep(100);
}
return 0;
}tylko nie wiem czy jest sens przeklejac kody ktore dostepne sa tutaj:
https://github.com/libopencm3/libopencm3...s/stm32/f4
i jeszcze jakis przyklad z aktualnych moich testow libopencm3... fragment obslugi UART pod ktory podpiety jest GPS...
Kod:
void GPS_HardwareInit(void)
{
/********************************************************************************
* Enable Clock
********************************************************************************/
rcc_periph_clock_enable(RCC_GPIOC);
rcc_periph_clock_enable(RCC_USART3);
/********************************************************************************
* Configure GPIO
********************************************************************************/
/* PC10 - TX, PC11 - RX */
gpio_mode_setup(GPIOC, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO10 | GPIO11);
/* PC12 - Reset */
gpio_mode_setup(GPIOC, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO12);
/* PC11, PC12 - Out OpenDrain */
gpio_set_output_options(GPIOC, GPIO_OTYPE_OD, GPIO_OSPEED_25MHZ, GPIO11 | GPIO12);
/* AF7 - USART3 */
gpio_set_af(GPIOC, GPIO_AF7, GPIO10 | GPIO11);
/* PC12 - Reset Off */
gpio_set(GPIOC, GPIO12);
/********************************************************************************
* Configure USART
********************************************************************************/
usart_set_baudrate(USART3, 9600);
usart_set_databits(USART3, 8);
usart_set_stopbits(USART3, USART_STOPBITS_1);
usart_set_mode(USART3, USART_MODE_RX);
usart_set_parity(USART3, USART_PARITY_NONE);
usart_set_flow_control(USART3, USART_FLOWCONTROL_NONE);
/********************************************************************************
* USART IRQ
********************************************************************************/
nvic_set_priority(NVIC_USART3_IRQ, 0);
nvic_enable_irq(NVIC_USART3_IRQ);
usart_enable_rx_interrupt(USART3);
/********************************************************************************
* Enable USART
********************************************************************************/
usart_enable(USART3);
}
void usart3_isr(void)
{
if (((USART_CR1(USART3) & USART_CR1_RXNEIE) != 0) && ((USART_SR(USART3) & USART_SR_RXNE) != 0))
{
GPS_ParseChar(usart_recv(USART3));
if (GPSNmea.msg_available)
{
GPS_ParseNMEA();
GPSNmea.msg_available = false;
}
}
}